How to Repair Window Screens

Repairing and replacing screens fits easily under the heading of do-it-yourself projects. Screen repair is among the simplest of jobs. In this document you will find information about: Screen Repairs Replacing Screening in Wood Frames SINGLE SOURCE SOLUTION Call today and let us show you how Magnolia can be your single source solution for all of your window screen component needs.  Call today... 1-800-638-6912 Replacing Screening in Metal Frames Frame Repairs Painting Screens Cleaning Screens Tools and Materials   18" x 16" or 18" x 14" Screening Screwdriver Exterior Trim Paint Snap-On Screen Patches Long-Nosed Pliers 1x2 and 1x4 Stock Heavy-Duty Scissors Metal Snips Paint Solvent Heavy-Duty Stapler Tack Hammer Sandpaper, 80 or 100 Grit Try Square or Framing Square Spline Tool Clean-Up Rags Measuring Tape or Rule Sawhorses Garden Hose Utility Knife Screws Stiff-Bristled Brush Claw Hammer Dowels, 3/8" or 1/2" 2x4 Boards Screen Molding Mending Plates 2 C-Clamps, 3" or Larger Nail Set Shop Vacuum with Upholstery Brush Exterior Wood Glue Drill and Bits Paintbrush or Pad Plastic Spline Material   STEP 1 FIG. 1 - Unravel several strands from the patching material or use a ready-made, snap-on patch. FIG. 2 - Slip the bent strands of the patch through the screening, then bend them back to hold the patch in.   SCREEN REPAIRS   You can easily patch most small holes. It's only when a hole exceeds about 3" in diameter that the screening itself needs to be replaced.   Measure hole sizes and purchase ready-made, snap-on repair patches or cut them from new screening. A patch should be at least 1/2" larger in diameter than the hole. For bigger holes, the patch should be as much as 1" larger.   For metal and most fiberglass screen patches, use this procedure: Unravel a number of strands around the edges of the patch one or two rows back from the edges, depending on the patch size (Fig. 1). Then weave the strands through the screening and bend them tight (Fig. 2). You can usually bend the strands with your fingers, but if the patch is heavy duty, you may need long-nosed pliers. Plastic patches need a touch of household cement on the ends of the strands after they've been woven through.   You can patch small holes–1/4" to 3/8"–with a small amount of household cement (Fig. 3). This glue patch will be next to invisible.   Fiberglass and plastic screens are tough to patch and should probably be replaced.     STEP 2 FIG. 4 - For the cleat-and-wedge method of stretching a new screen, first staple the screening across the top of the frame. FIG. 5 - Then nail down the longer end between two cleats.   FIG. 6 - Insert wedges between the cleats and frame, tapping them in gently until the screen pulls taut. FIG. 7 - Now you can staple the screening along the bottom and both sides. FIG. 8 - For longer frames, place the unit on sawhorses over 2x4s or plywood. The center is clamped and the ends are gently raised on 2x4 blocks.   REPLACING SCREENING IN WOOD FRAMES   To remove the old screening, pry off the screen molding, starting in the center of a strip and working toward the ends. Try not to break it.   Your local retailer can help you decide what type of new screening to use. For general household screening, you need a mesh of 18" x 14" or finer (these are the stand counts in each direction, per inch).   With wooden window and door screens, it is important to stretch the screen fabric drum-tight for a neat and long-lasting job. For the wedge method of stretching, you'll need some 1x2 stock in a length slightly wider than the window or door and some 1x4 stock from which to saw out the wedges.   Cut your new screening at least 1' longer and 1' wider than the unit to be recovered.   Staple the screening across the top edge (Fig. 4). Then install the 1x2 cleats with the bottom cleat nailed to a bench or other flat surface. Roll the screening over it, then nail on the top cleat (Fig. 5).   Insert the wedges between the cleats and screen frame, tapping the wedges in until the screen has been pulled taut. Fig. 6 shows the procedure.   Staple the screening at the bottom, then along the sides. Put a staple in every few inches (Fig. 7).   Snip off any excess screening, and use brads to refit the screen moldings. Countersink the brads and fill the holes with wood putty.   The cleat-and-wedge method works well with window screens and halves of doors, but there's a better method of stretching screen material on larger units, such as doors. You'll need a pair of sawhorses with two 2x4s about the same length as the screen placed across them (or use a sheet of plywood). Place the stripped fame on the boards, holding the center with C-clamps. Then lift each end and insert short 2x4 blocks to bow them (Fig. 8). Bowing needs to be done slowly and gently to keep from snapping the frame.   Now staple the screen in place tightly, starting at the center brace. Remove the 2x4 blocks and the screen will be quite taut as you replace the screen moldings.     STEP 3 FIG. 9 - To replace screening in a metal frame, carefully pry out the splines with a screwdriver that's slightly smaller than the spline. FIG. 10 - Cut the screening to the exterior frame size.   REPLACING SCREENING IN METAL FRAMES   Aluminum screens or screen doors require a different technique.   Without kinking the metal frame, remove the splines that hold the old screen in place (Fig. 9). Check to see if new splines are needed. For replacement, vinyl splining is excellent. It comes in rolls of various widths.   Use a square to make sure the frame is still in decent shape. Reshape it if not.   Cut new screening to the frame's outside measurements (Fig. 10).   Next, force the screen's edges into the channel on the top and one side using the convex-edged wheel of a spline or screen installation tool (Fig. 11). These tools are available with different-width rollers–use one that matches the channels in your screen frame. Use short strokes for the best results. A putty knife will work, too.   With a sharp utility knife, cut the screening to fit the two remaining sides. Use the outside edge of the retaining channel as a guide. Use the spline tool to roll the screening into the remaining grooves.   Use the concave-edged wheel of the spline tool to roll the retaining strips or splines into the channels (Fig. 12). As before, make short strokes. As the spline goes in, it will pull the screening taut. To complete the installation, cut off any excess screening around all four sides.     STEP 4 FIG. 11 - Roll the screening down into the channel using the convex wheel of the spline tool. FIG. 12 - Roll the spline into the channels with the concave wheel of the spline tool.   FIG. 13 - Screws and dowels are useful where the outside layer of wood has been weakened, while mending plates go on simply and quickly.   FRAME REPAIRS   Screen frame repairs are easiest to make on wooden screen doors and windows. You may need wood glue, dowels, corrugated or chevron fasteners, mending plates and wood screws, depending on the condition of the frame. The fasteners work best on mitered-corner screen frames.   If the joint is slightly loosened but the material is intact, open it up enough to apply wood glue. Use a glue that's suited for outdoor exposure (ask your retailer).   Along with re-gluing, you may want to install a mending plate of the proper size. Flat and angled plates are available in many sizes; use the largest size that fits without causing problems. Secure the plates with wood screws, which are often included. Make sure the screws don't come through the back of the frame.   For making a simple repair at a slightly damaged corner, you have two choices. You can use a wood screw from the undamaged edge or a dowel from either edge (with glue). Drill and countersink for the wood screw, using as large a size as practical. A 2-1/2" No. 10 screw is probably the smallest screw that's strong enough to last. Fill the countersink hole with putty.   For a dowel, drill for at least a 3/8" diameter dowel. A 1/2" dowel is even better. Dowels need to be slightly undersized for their holes with a tap fit. Take care to see that the dowel runs on into undamaged wood.   Coat the dowel with glue and tap it into the hole.   With dowel and wood screw repairs, the holes should extend into both pieces of the frame. If the frame shows signs of twisting, you'll need to use two slightly smaller dowels or two wood screws.   Fig. 13 shows four types of screen corner repairs using a wood screw, dowel and two types of mending plates.   Aluminum frame repairs are limited to rebracing of corners. Or you can get extruded metal frame stock and make new screens. A cross-brace kit is also available, if needed, with turnbuckles and clamps to draw a sagging screen door back into square and hold it there.   For frame or corner repairs, check the squareness of the frame, then use mending plates and sheet metal screws to make repairs or to reinforce those corners. Be sure that the mending plates you use are the same material as the frame. This will help prevent corrosive electrolysis between dissimilar metals.     STEP 5 - PAINTING SCREENS   In most cases, only wood-framed screens ever need painting. Choose the paint to match the window frames. Select painting tools that are suited for use on small surfaces. If you have the old screening off and find that the frame needs painting, do it while the screen is off.   On wood screens, remove the old, torn screening as the paint coat under the molding and screen provides protection. Make sure the coating is light, though, so the molding fits on replacement.   Don't try painting screen mesh. If your screens have galvanized screen mesh, replace them if they rust. Painting aluminum or fiberglass screening is only a waste of time and paint.     STEP 6 FIG. 14 - Sometimes, simply spraying screens with water will clean them sufficiently; other times, scrubbing with a brush and detergent is needed.   CLEANING SCREENS   To clean screens, first try vacuuming them while installed. An upholstery nozzle usually does the trick.   In some cases, airborne dirt cannot be removed simply by vacuuming. Then the screens must be taken off and washed. With luck, a hard spray from a garden hose will do the job (Fig. 14). In other cases, you'll need to scrub the screens. Do this with a stiff-bristled brush and a mild detergent solution, and finish by rinsing with the hose.